ALLIANCE AE7133 Manuale di Servizio Pagina 72
- Pagina / 125
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
60549 71
Section 8 Service Procedures Unique to Electronic Control Model Dryers
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
• If branch circuit to dryer is 15 feet (4.50m) or
less in length, use U.L. (Underwriters
Laboratories) listed No. 10 A.W.G. wire
(copper wire only), or as required by local
codes. If over 15 feet (4.50m), use U.L.
(Underwriters Laboratories) listed No. 8
A.W.G. wire (copper wire only), or as
required by local codes. Allow sufficient
slack in wiring so dryer can be moved from
its normal location when necessary.
• The power cord (pigtail) connection between
wall receptacle and dryer terminal block is
NOT supplied with dryer. Type of pigtail
and gauge of wire must conform to local
codes and with instructions mentioned in
previous paragraph.
• The method of wiring the dryer is optional
and subject to local code requirements. Refer
to Figure 53.
b. Electrical Connection (Three-Wire)
IMPORTANT: This dryer is grounded to neutral
conductor at the terminal block. If the dryer is
installed in a mobile home, or if local codes do not
permit grounding through the neutral, proceed as
shown on Pages 76 and 77.
(1) Remove the screw and terminal block
access cover from the rear of dryer cabinet.
(2) Insert ends of wires through power supply
hole (containing proper strain relief) in rear
of dryer cabinet. Refer to page 75. Connect
the power cord, or direct wiring, to the
appropriate terminal block terminals as
follows:
Through Serial No. S6271975XG–Use
the nuts and washers from the accessories
pack in the envelope shipped inside the
dryer cylinder.
Starting Serial No. S6271976XG–Use the
three-wire binding (10-32x3/8") screws
from the accessories pack in the envelope
shipped inside the dryer cylinder.
If the dryer had previously been connected
with a four-wire power cord, remove the
four-wire cord by reversing procedures
under four-wire power cord. Refer to pages
76 and 77.
IMPORTANT: Use only a new U.L. listed No. 10
(copper wire only) three conductor power supply
cord kit rated 240 Volts (minimum) 30 Amperes
and labeled as suitable for use in a clothes dryer.
(3) Through Serial No. S6271975XG–
Tighten these outer nuts firmly using a 3/8"
deep well socket.
Starting Serial No. S6271976XG–Tighten
these wire-binding screws firmly.
IMPORTANT: Failure to tighten either the nuts or
screws firmly may result in wire failure at the
terminal block.
(4) Secure the strain relief to the power cord, or
wires, where they enter the dryer cabinet.
(5) Reinstall access cover and screw.
To reduce the risk of electric shock,
disconnect the electrical service to the
dryer before proceeding.
W135
WARNING
- Home Laundry 1
- Table of Contents 2
- Section 1 4
- Safety Information 4
- Section 1 Safety Information 5
- Section 2 6
- Introduction 6
- Model Identification 7
- How Your Dryer Works 8
- Section 2 Introduction 9
- Section 3 10
- Troubleshooting 10
- 10 60549 11
- POSSIBLE CAUSE TO CORRECT 11
- 12 60549 13
- 14 60549 15
- 16 60549 17
- Section 4 18
- Grounding 18
- 18 60549 19
- Figure 3 19
- Figure 4 20
- 20 60549 21
- Figure 5 21
- Figure 6 21
- DRY1071S 22
- DRY1794S 23
- DRY1795S 23
- DRY1075S 24
- DRY1796S 24
- Section 5 Service Procedures 25
- DRY1055S 27
- Figure 11 28
- 28 60549 29
- Figure 12 29
- Figure 13 29
- 30 60549 31
- Figure 14 31
- Wiring Schematic 32
- 32 60549 33
- Figure 16 33
- Figure 17 34
- 34 60549 35
- Figure 18 35
- DRY1797S 37
- DRY855S 37
- Figure 20 38
- 38 60549 39
- Figure 21 39
- Figure 22 40
- Figure 23 40
- 40 60549 41
- Figure 24 41
- Figure 25 42
- 42 60549 43
- Figure 26 43
- Figure 27 44
- Figure 28 44
- 44 60549 45
- Figure 29 45
- Figure 30 45
- Figure 31 46
- 46 60549 47
- Figure 32 47
- 48 60549 49
- Figure 33 49
- Figure 34 50
- 50 60549 51
- Figure 35 51
- Figure 36 52
- 52 60549 53
- 54 60549 55
- Section 6 56
- Adjustments 56
- 56 60549 57
- Figure 38 57
- Section 7 58
- Figure 40 59
- 58 60549 59
- 1 - 3 60
- 60 60549 61
- Figure 43 61
- Figure 44 61
- Figure 45 62
- Burner Orifice SpudVent Screw 62
- Figure 48 64
- Figure 49 64
- 64 60549 65
- Figure 50 65
- MEMORY RECALL 66
- ON / SELECT STATUS 67
- AUTOMATIC 67
- TIME DRY 67
- 60549 67 68
- 68 60549 69
- AUTOMATIC CYCLES 69
- Figure 51 69
- Figure 52 70
- 70 60549 71
- Figure 53 71
- 60549 71 72
- 72 60549 73
- Figure 54 73
- Figure 55 74
- 74 60549 75
- Figure 56 76
- 76 60549 77
- Figure 57 77
- Figure 58 77
- 60549 77 78
- DRY1068S 79
- Figure 60 80
- Figure 61 90
- 90 60549 91
- Section 9 92
- 92 60549 93
- Section 10 94
- Wiring Diagrams 94
- 94 60549 95
- 96 60549 97
- MODELS NG7519 AND NG7319 98
- 98 60549 99
- MODELS NE7513 AND NE7313 99
- Through Serial No. S6271975XG 100
- 100 60549 101
- 102 60549 103
- MODELS NG6519 AND NG6319 104
- 104 60549 105
- MODELS NE6513 AND NE6313 106
- 106 60549 107
- MODEL NE6513 AND NE6313 107
- MODELS NG4519 AND NG4319 108
- Through Serial No. S6242593XD 108
- 108 60549 109
- Section 10 Wiring Diagrams 110
- 110 60549 111
- MODEL VE5013 111
- MODEL NG4719 AND NG4619 112
- 112 60549 113
- MODEL NE4713 AND NE4613 114
- 114 60549 115
- MODEL NE4513 AND NE4313 116
- 116 60549 117
- 118 60549 119
- 120 60549 121
- MODELS NG2119 122
- 122 60549 123
- MODELS NE2113 123
- 124 60549 125
Prodotti e manuali riguardandi Asciugatrici elettriche ALLIANCE AE7133
(28 pagine)
(172 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.465 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale